What are the 7 steps for a pre-trip inspection?
What are the 7 steps for a pre-trip inspection?
CDL test – 7 Step Inspection Method – see description
- Vehicle Overview.
- Check engine compartment.
- Start engine and inspect cab.
- Turn off engine and check lights.
- Do walkaround inspection.
- check signal lights.
- start engine and check.
What things should you check during a trip CDL?
Trip Inspection
- Tires, wheels and rims.
- Brakes.
- Lights and reflectors.
- Brake and electrical connections to trailer.
- Trailer coupling devices.
- Cargo securement device.
What is the second thing you should do on a pre-trip inspection?
Next step for the pre-trip inspection is to check the side of the trailer and the tandems.
- Wall – Make sure the wall is not damaged.
- Lights – Lights should be on and flashing.
- Tires – Tires should be properly inflated and have decent tread.
- Hub seal – Make sure it’s not leaking and wiped with oil if transparent.
What is the first step of the seven step pre-trip inspection?
1: Vehicle Overview Review Last Vehicle Inspection Report. Drivers may have to make a vehicle inspection report in writing each day. The Page 2 motor carrier must repair any items in the report that affects safety and certify on the report that repairs were made or were unnecessary.
Which of the following is not part of the pre-trip inspection?
Which of these is not part of the pre-trip inspection of the engine compartment? A Valve clearance. See: Step 2 – Check Engine Compartment. Valve clearance is not on the checklist.
What are two main things to look for ahead CDL?
The two key things you should be checking for ahead of time are traffic and road conditions. Keep an eye out for vehicles entering the highway, merging into your lane, or turning. Keep an eye out for slowing automobiles’ brake lights.
Where are the blind spots on a truck?
On Both Sides of the Truck On the driver’s or left side of the truck, the blind spot extends outward for one lane, almost three-fourths of the way to the back of the trailer. The passenger or right side of the truck has a larger blind spot. The blind spot extends outward for two lanes.
Which of these is not something you should check during the pre-trip inspection of the engine compartment?
Which of these is not a part of the pre-trip inspection of the engine compartment? The condition of the hoses and electrical wire insulation will be checked in Step 2 (Check Engine Compartment) of the Seven-Step Inspection Method. You will not, however, remove the valve cover in order to examine the valve clearance.
Which of these pieces of emergency equipment should be carried at all times in your vehicle?
The following emergency equipment should always be carried in your vehicle: fire extinguisher(s), spare electrical fuses (if the vehicle uses them), warning devices for parked vehicle.
What is the most important thing to inspect when you start your vehicle CDL?
Safety is the most important reason you inspect your vehicle, safety for yourself and other road users.
How many blocks should a CDL driver look ahead?
A good truck operator will look at least 12 to 15 seconds ahead. That means looking ahead a distance that the truck will travel in 12-15 seconds. Obviously, this distance is relative to speed. At lower speeds it is the distance of about 1 block.
What you Cannot see in your mirrors is said to be?
Visit the Claims centre However, there is a surprisingly large area around our cars that we cannot see simply by looking ahead, or even at our mirrors. This is called the “blind spot,” and is sometimes forgotten by even experienced drivers.
What is the first step of the seven step pre trip inspection?
What fire extinguisher is needed for dot?
Vehicles that do not transport hazardous vehicles must carry either one fire extinguisher rated 5 B:C or greater or two fire extinguishers rated 4 B:C or greater.
Does DOT require spare fuses?
Power units for which fuses are needed to operate any required parts and accessories must have at least one spare fuse for each type/size of fuse needed for those parts and accessories. (2) At least 6 fusees or 3 liquid-burning flares.
Which of the following is the most important reason for doing a pre-trip inspection?
The most important reason to perform a pre-trip inspection is for your safety. It can be dangerous to go out on the road with a load that is not secured, brakes that are damaged, wiring that is not connected, etc.
How to perform a Class A CDL pre trip inspection?
Be positive and polite to the inspectors.
How to pass your CDL pre trip?
The MVI decal is valid until September 2016 – the end of the month.
How to remember pre trip inspection CDL?
Step One: Break the Sections Down&Use An Association. We’ll get into this technique in a second,but the first step of performing a pre trip inspection is to
What is CDL pre trip?
Front of the truck