How do I reset my Eaton UPS card?
How do I reset my Eaton UPS card?
Type 0 and press Enter to return to the Network Card-MS main menu. 6. From the main menu, type 1 for the Reset menu and press Enter to save this new configuration. Type 1 again and press Enter to Restart the card from the boot.
What is the default IP address for APC UPS?
192.168.2.66
The default IP address is 192.168. 2.66 with a subnet mask of 255.255. 255.0.
How do I access APC UPS interface?
Connect to the UPS/device serial port using the correct APC configuration cable….9600 bps, 8 data bits, no parity, 1 stop bit, and no flow control.
- Apply the port settings to establish the connection.
- Press enter 3-5 times to display the username prompt.
- Use the default username and password of “apc”.
What is the default IP address of APC UPS?
Can I use UPS without battery?
Yes. The outlets will operate without any battery backup protection. Surge protection will continue to function normally. If your model has a display screen, there is a button on the front panel that can be used to mute the alarm.
How do I reset my apc password?
Press the Reset button a second time immediately while the LED is flashing to reset the user name and password to their defaults temporarily. Then press ENTER as many times as necessary to redisplay the User Name prompt, then use the default, apc, for the user name and password.
How do I use APC UPS first time?
C60 Quick Start Guide
- When taking the UPS out of the box for the first time:
- Plug the UPS into an electrical outlet, allowing the UPS to charge for at least 6 hours prior to first use.
- Connect your critical equipment to the UPS outlets at the rear of the unit.
What happens when UPS runs out of battery?
When the UPS runs on battery operation and the battery becomes discharged, the UPS automatically switches off. Resolution: Note: The UPS will continue to recharge its battery in the Off state, as long as there is some voltage present on the electrical circuit.
What happens when a UPS battery dies?
A stand-by unit will Fail on when the battery dies because the battery is only used when the power goes out. So if the battery goes bad when the power is on, nothing will happen as far as you can tell until the power goes out and so does the system connected to the UPS.
What is the default username and password for APC PowerChute?
You should see 2 text fields where you can enter a username and a password. The default username for your APC PowerChute Bussiness Edition is Pingo. The default password is Ura. Enter the username & password, hit “Enter” and now you should see the control panel of your router.
How do I know if my UPS is fully charged?
Just plug it in to a power source and check the read out There is a battery indicator on the read out when you first plug it in the battery is fully charged. You will be able to see it if the power goes out and it has to charge. Sorry, there was a problem.
How do I set up the UAP-AC-M-Pro with unifi controller?
Ensure the UAP-AC-M-PRO is powered on, and then launch the UniFi Controller software. Go to the Devices page, and the UAP-AC-M-PRO will show up as Pending Approval (Wireless). Click Adopt.
How do I mount the unifi AP on the wall?
The UniFi AP can be mounted on the wall or ceiling. Perform the steps for the appropriate installation: Wall Mount 1. Position the Mounting Bracketat the desired location on the wall with the Arrowpointing up. 2. Mark the four mounting holes, and use a 6 mm drill bit to drill the holes.
How do I mount the UAP-AC-M-Pro on the wall?
The UAP-AC-M-PRO can be mounted on a pole or mast, or on a wall. Perform the steps for the appropriate installation. Note: Secure the Mounting Bracket directly to a stud or other structurally stable surface using appropriate fasteners. Note: Screws shown not included.
How do I enable wireless adoption on the UAP-AC-M-Pro?
The UAP-AC-M-PRO supports wireless adoption into your UniFi Wi-Fi network. This feature requires a currently managed UniFi AP operating with the following configuration: The Secondary port is a Gigabit Ethernet port used for bridging. Restart Press and release the Reset button quickly.