How many watts is a 6V6?
How many watts is a 6V6?
The data sheet information supplied by the tube manufacturers’ design centers, list the typical operation of an audio output stage for a single 6V6 as producing about 5 W of continuous power, and a push-pull pair about 14 W.
Can I put 6V6 in a 6L6 amp?
The general answer is no, for the most part, 6L6 and 6v6 tubes are not interchangeable as they don’t bias close enough. Amps are calibrated to use specific valves (6v6, 6L6, EL84, etc.) and are not always well suited to multiple valve usage without circuit modifications.
Can I replace 6V6 with EL34?
I wouldn’t use a 6V6 in place of an EL34, because it might not survive very long. Two better choices would be KT77 or 6CA7. Even if you swap out EL34 for EL34 tubes, re-biasing is highly recommended as cheap insurance against nasty, deadly side effects of imbalance or overload.
How much current does a 6V6 draw?
6V6 – 6V6 GT BEAM POWER TUBE
| Heater Voltage (AC/DC) | 6.3 | volts |
|---|---|---|
| Heater Current | 0.45 | ampere |
| Heater Warm-up Time (Average) | 11 | seconds |
Are 6v6 tubes good?
These tubes sound great, period. They do clean with smooth clear high end. On the other end of the spectrum big fat bass notes that are well defined having a piano like quality are produced. Crank up the gain and you will get everything from a nice crunch to all out screaming distortion.
Can I put 6L6 in a EL34 amp?
Re: 6L6 to El34 tube change One if the PT’s heater current capacity. 6L6 heaters draw 0.9A each whereas EL34 heaters draw 1.5A, so a pair of tubes will add an additional 1.2A to the heater supply requirement. Two is the output tube socket wiring.
Do tubes make a difference in amps?
Therefore, a short plate tube is better for guitar amplifiers because we want low microphonics. The tone signature of the harmonics also is slightly different from one brand of power tube to another. Therefore, one brand of tube may be more to your liking.
Do guitar amp tubes have to be matched?
Power tubes, unlike preamp tubes, do generally need to match. This is because each power tube needs to have an identical account of idle plate current. The amplification characteristics of the tubes also need to match up when they are used in a guitar amp, for example.
Can you swap 5881 with 6L6?
In many cases, 6L6s can be safely substituted for 5881s, but not vice versa. In a few cases, where the plate voltage tolerance is high enough, 5881s can be used in amps designed for 6L6s.
Do I need to bias my tube amp?
Conclusion: You’ll need to bias most tube amps if you change the tubes. This is because you cannot buy tubes with a similarly matched resistance. You should always buy a matched pair or a matched quad of tubes, but the chances of them matching your current pair are very small.
Where are JJ tubes made?
Slovakia
JJ Electronic, s.r.o is a Slovak electronic component manufacturer, and one of the world’s remaining producers of vacuum tubes. They are based in Čadca, in the Kysuce region of Slovakia. Most of the products that JJ offers are audio receiving tubes. These vacuum tubes are mainly used for guitar and hi-fi amplifiers.
What is the difference between 6L6 and 5881 tubes?
The 6L6GC tube is a 30W valve. The 5881 valve is a 23W valve. So that’s quite a big difference. So the 6L6GC will give you more power and more clean headroom.
Can I replace EL84 with EL34?
In the specific case of swapping an EL34 for an EL84, you actually can’t swap them because the two different tubes have a different number of pins on their sockets.